What happens when H3PO3 is heated? | Class 12 Chemistry Chapter The p-Block Elements, The p-Block Elements NCERT Solutions

How the following conversions can be carried out?

(i) Propene to propan-1-ol

(ii) Ethanol to but-1-yne

(iii) 1-Bromopropane to 2-bromopropane

(iv) Toluene to benzyl alcohol

(v) Benzene to 4-bromonitrobenzene

(vi) Benzyl alcohol to 2-phenylethanoic acid

(vii) Ethanol to propanenitrile

(viii) Aniline to chlorobenzene

(ix) 2-Chlorobutane to 3, 4-dimethylhexane

(x) 2-Methyl-1-propene to 2-chloro-2-methylpropane

(xi) Ethyl chloride to propanoic acid

(xii) But-1-ene to n-butyliodide

(xiii) 2-Chloropropane to 1-propanol

(xiv) Isopropyl alcohol to iodoform

(xv) Chlorobenzene to p-nitrophenol

(xvi) 2-Bromopropane to 1-bromopropane

(xvii) Chloroethane to butane

(xviii) Benzene to diphenyl

(xix) tert-Butyl bromide to isobutyl bromide

(xx) Aniline to phenylisocyanide

Give simple chemical tests to distinguish between the following pairs of compounds.

(i) Propanal and Propanone

(ii) Acetophenone and Benzophenone

(iii) Phenol and Benzoic acid

(iv) Benzoic acid and Ethyl benzoate

(v) Pentan-2-one and Pentan-3-one

(vi) Benzaldehyde and Acetophenone

(vii) Ethanal and Propanal

A 5% solution (by mass) of cane sugar in water has freezing point of 271 K. Calculate the freezing point of 5% glucose in water if freezing point of pure water is 273.15 K.

A solution of glucose in water is labelled as 10% w/w, what would be the molality and mole fraction of each component in the solution? If the density of solution is 1.2 g mL^-1, then what shall be the molarity of the solution?

Henry's law constant for CO₂ in water is 1.67 x 10⁸Pa at 298 K. Calculate the quantity of CO₂in 500 mL of soda water when packed under 2.5 atm CO₂ pressure at 298 K.

Calculate the mass of a non-volatile solute (molar mass 40 g mol^-1) which should be dissolved in 114 g octane to reduce its vapour pressure to 80%.

The vapour pressure of pure liquids A and B are 450 and 700 mm Hg respectively, at 350 K. Find out the composition of the liquid mixture if total vapour pressure is 600 mm Hg. Also find the composition of the vapour phase.

Calculate the mole fraction of benzene in solution containing 30% by mass in carbon tetrachloride.

How many mL of 0.1 M HCl are required to react completely with 1 g mixture of Na₂CO₃ and NaHCO₃ containing equimolar amounts of both?

If NaCl is doped with 10^-3mol % of SrCl₂, what is the concentration of cation vacancies?

Give evidence that [Co(NH₃)₅Cl]SO₄ and [Co(NH₃)₅SO₄]Cl are ionization isomers.

Time required to decompose SO₂Cl₂to half of its initial amount is 60 minutes. If the decomposition is a first order reaction, calculate the rate constant of the reaction.

Discuss the nature of bonding in the following coordination entities on the basis of valence bond theory:

(i) [Fe(CN)₆]^4-

(ii) [FeF₆]^3-

(iii) [Co(C₂O₄)3]^3-

(iv) [CoF₆]^3-

Write down the IUPAC name for each of the following complexes and indicate the oxidation state, electronic configuration and coordination number. Also give stereochemistry and magnetic moment of the complex:

(i) K[Cr(H₂O)₂(C₂O₄)₂].3H₂O

(ii) [Co(NH₃)₅Cl]Cl₂

(iii) CrCl₃(py)₃

(iv) Cs[FeCl₄]

(v) K₄[Mn(CN)₆]

Predict the products of electrolysis in each of the following:

(i) An aqueous solution of AgNO₃ with silver electrodes.

(ii) An aqueous solution of AgNO₃with platinum electrodes.

(iii) A dilute solution of H₂SO₄with platinum electrodes.

(iv) An aqueous solution of CuCl₂ with platinum electrodes.

Compare the general characteristics of the first series of the transition metals with those of the second and third series metals in the respective vertical columns. Give special emphasis on the following points:

(i) electronic configurations,

(ii) oxidation states,

(iii) ionisation enthalpies, and

(iv) atomic sizes.

Write the name and structure of one of the common initiators used in free radical addition polymerisation.

Calculate the mole fraction of benzene in solution containing 30% by mass in carbon tetrachloride.

Write down the reactions taking place in different zones in the blast furnace during the extraction of iron.

Why is the extraction of copper from pyrites more difficult than that from its oxide ore through reduction?